Whether this is your first plumbing repair or your tenth, Campbell Plumbing Company is ready to help. We serve homeowners, renters, landlords, property managers, and commercial operators throughout Campbell and the surrounding area, handling everything from a dripping faucet to a full sewer line replacement. We are available every day from 8 AM to 11 PM, so evening calls and weekend jobs are on the table. When you call, you get no-pressure estimates, priced up front, before anything is scheduled. Call and we'll handle the leaks, drains, and fixtures.
Most plumbing problems give some warning first, and getting ahead of them is always easier than dealing with the aftermath. We handle the full range of residential and commercial plumbing repair and installation, from a slow kitchen drain to a main shutoff valve that no longer closes all the way. The work covers every fixture, every pipe, and every connection in between, and the plumbing done properly, start to finish, is what every job here is built around.
A clogged sink or a slow bathroom drain is one of the most common calls we get. Kitchen drain cleaning, bathroom drain cleaning, and floor drain clearing are straightforward jobs when they are caught early. When a drain backs up repeatedly or multiple drains slow at once, that pattern often points to a blockage deeper in the main line rather than at the individual fixture. We clear the immediate clog and let you know if the main line needs attention.
A leak behind a wall or under a floor can run for weeks before it shows up as a water stain or a spike on the water bill. We use pressure testing and electronic detection to find hidden leaks without tearing out more than necessary. Once located, we repair broken pipes, damaged water lines, and corroded sections. Slab leaks get their own dedicated section below, but if you are seeing wet spots on the floor or unexplained water pressure changes, that is where the conversation usually starts.
A running toilet can waste a significant amount of water before anyone notices. We handle toilet repair and replacement across the board, whether the issue is a toilet that will not flush, a float that keeps running, or an overflow situation that needs immediate attention. Faucet repair and replacement covers dripping kitchen faucets, bathroom faucet installation, and fixture swaps of all kinds. We also install and replace garbage disposals, including units that have stopped working, are jamming, or are simply past their useful life.
Low water pressure can have more than one cause. Sometimes the issue is at a single fixture, which points to a clogged aerator or a failing valve. When pressure is low throughout the house, the cause is often a failing pressure-regulating valve or a problem at the main shutoff. We diagnose where the pressure loss is happening before recommending a repair, which keeps the scope of the job accurate and the cost in line with what the problem actually is.
We test every fixture. We check every valve. We leave it dry.
Getting your water flowing again is easier than you think, and a water heater problem is one of the faster repairs to scope on the phone. We handle water heater repair and replacement for both tank and tankless units. No hot water, a water heater that is making noise, a unit leaking at the base, or one that is simply not keeping up with demand are all situations we work through regularly. The cause of a leak explained, not just the patch, is how we approach any diagnosis before recommending a full replacement. Sometimes a heating element or a valve is the fix. When the unit is past its useful life, we help you pick the right replacement for the household's hot water demand and the space available. Tankless water heater installation gets a fuller treatment in the regional services section below, but we repair and service existing tankless units as well. Call for a quote and we will walk through what the job involves and what it costs before anything is scheduled. Give us a call and we will get the water back on.
Hearing a running toilet or a drip behind the wall is one thing. A sewer backup is a different level of urgency. We handle sewer line repair, sewer line replacement, main line clogs, and sewage backup situations for both residential and commercial properties. A sewer camera inspection is often the first step, because it shows exactly what is happening inside the pipe: root intrusion, grease buildup, a collapsed section, or simple blockage. That picture determines whether hydro jetting clears the problem or whether a section of pipe needs to come out. We speak to the line from the house to the city connection, and drain and pipe work carried out to code is the standard every job is held to.
Property managers, landlords, and commercial operators have different scheduling pressures than a single-family homeowner. A backed-up drain in a restaurant kitchen or a failed water heater in a multi-family building needs a fast answer, not a call back in three business days. We work with apartment buildings, condos, townhouses, office buildings, restaurants, and commercial spaces throughout the area. Our availability window of 8 AM to 11 PM, every day, including evenings and weekends, gives property managers the flexibility to schedule around tenants and business hours. Most jobs can be scoped and priced on the phone before anyone shows up, which keeps the process straightforward for everyone involved. We pick up the phone and get it handled.
Campbell sits in a part of Santa Clara County where the housing stock tells the story. Post-war tract homes built on slab-on-grade foundations, mid-century construction with aging galvanized and copper supply lines, and smaller Bay Area lots where space is at a premium all shape the kind of plumbing work that comes up most often here. The three services below reflect what this area's homes actually need.
A slab leak happens when a supply line cast into or running beneath a concrete foundation develops a break. In Santa Clara County, soil movement and the age of the copper piping in older construction make this a common problem. The signs are subtle at first: a warm spot on the floor, a rise in the water bill, or pressure that drops without explanation. We locate the break using pressure testing, electronic detection, and listening equipment, so the repair targets the actual failure point. Depending on where the leak is and how far the pipe has degraded, repair options include spot repair, pipe rerouting above the slab, or a full repipe. The cause of a leak explained, not just the patch, shapes every recommendation we make here. Call for a plumbing estimate and we will walk through what the inspection involves.
Bay Area homes run hot water hard, and a tankless water heater delivers it on demand without keeping a full tank heated around the clock. In Campbell, where most homes use natural gas, a tankless upgrade is often a straightforward swap: the gas line is already in place, and the new unit vents similarly to the old one. Installation covers gas line or electrical supply assessment, proper venting, and removal of the old tank unit. Smaller home footprints in the area also make the wall-mounted form factor a practical advantage. We handle new installations and service existing tankless units that need flushing, part replacement, or repair.
Galvanized pipe has a lifespan, and a lot of mid-century Campbell homes have reached it. Pinhole leaks in older copper lines, persistent low pressure across multiple fixtures, and discolored water are all signs that the supply system has run its course. Whole-home repiping replaces the aging pipe throughout the house, typically with PEX or copper, working through walls and access points to restore full pressure and clean flow at every fixture. When a slab leak has occurred more than once, a full repipe is often the more durable answer than repeated spot repairs. The cost to repipe a house depends on the size of the home and the material, and we give you that number before the job starts.
When you call for a plumbing quote, the process is direct. We scope the job on the phone, give you a price, and confirm availability before anything is scheduled. There is no obligation to book, and the estimate does not cost you anything to get. We are available every day from 8 AM to 11 PM, which means evenings and weekends are on the table for both new jobs and follow-up work. Whether you need something handled soon or want to plan a few days ahead, we work around what your schedule allows. No-pressure estimates, priced up front, is how every call goes here.
One call. One plumber. One price, agreed first.
Call now and we'll get the water back where it belongs.
We serve Campbell and the communities nearby throughout Santa Clara County, including:
If you are in the area and need a plumber, call and we will confirm whether we can get to you.
The most common signs are a warm or wet spot on the floor, a water bill that has climbed without explanation, or water pressure that has dropped across the house. Some slab leaks also produce a faint sound of running water when everything is turned off. In Campbell, where many homes were built on slab foundations with copper supply lines cast into the concrete, this is one of the more common calls we receive.
We use pressure testing to confirm a leak is present in the supply system, then electronic detection and listening equipment to narrow down the location. That combination lets us identify where the break is before any concrete is touched. The goal is to open only what is necessary to reach and repair the actual failure point.
A single slab leak can often be repaired at the failure point, either by spot repair or by rerouting that section of pipe above the slab. When a home has had more than one slab leak, or when the pipe throughout the house is showing the same age-related wear, a full repipe is usually the more durable answer. We walk through the options and the cost difference on the call so you can make an informed decision.
Installation covers an assessment of the existing gas line or electrical supply, proper venting to the exterior, and the water line connections. We confirm what your current gas supply can support and what the venting at the chosen location requires before any work starts. If you are replacing a tank unit, we cover the differences in output and sizing on the call so the replacement matches how the home uses hot water.
The most common signs are no hot water, water that runs warm but not hot, a unit that is making popping or rumbling sounds, and visible rust or moisture around the base of the tank. Age is also a factor. When a tank is showing multiple symptoms at once, replacement is often more practical than repair, and we help you work through that on the call.
A failing water heater can reduce hot water pressure at fixtures throughout the house, cause discolored water at the faucet, and in the case of a slow leak, cause water damage to the floor or wall behind the unit. Sediment buildup in older tanks also reduces efficiency over time, which means the unit runs longer to deliver the same amount of hot water. Catching these signs early usually means a simpler repair or a planned replacement rather than an emergency call.
A burst supply line, a major leak that is actively causing water damage, a complete loss of hot water, a sewer backup that has shut down fixtures throughout the property, and a toilet overflowing with no sign of stopping all qualify.
If the situation is getting worse while you wait, call (669) 359-3289 right away.
We are available every day from 8:00 AM to 11:00 PM and take short-notice work for urgent situations.
A sewer smell inside the house typically points to a dry P-trap, a cracked or deteriorated wax ring at the base of a toilet, or a break in the sewer line itself. A dry trap is a simple fix. A cracked wax ring or a damaged line requires more investigation. If the smell is persistent or comes from multiple drains, that pattern usually points further into the main line and warrants a closer look.
We test every fixture and valve involved in the repair before the visit is complete. For supply line work, that means running water through the repaired section and checking for moisture at every connection. For drain work, we confirm the line is clear and flowing. We test every fixture. We check every valve. We leave it dry.
Rust-colored water at the faucet, low pressure across multiple fixtures, a metallic taste in the water, and pinhole leaks that keep appearing in the same section of pipe are the most common signs. In Campbell homes built before the 1970s, galvanized steel supply lines are often the source of these symptoms. Early copper installations can show similar problems where water chemistry or soil conditions have accelerated wear.
The most common reason is that the scope changes once the work is underway. A drain cleaning that reveals a damaged section of pipe, or a fixture replacement that uncovers corroded supply connections, may require additional work beyond what was scoped on the call. When that happens, we stop and explain what we found before proceeding. You agree to any change in scope before the additional work starts.
Campbell Plumbing Company handles residential and commercial plumbing throughout Campbell and the surrounding area, every day from 8 AM to 11 PM. Whether the job is a drain cleaning, a water heater replacement, a slab leak, a sewer line repair, or a whole-home repipe, the process starts with a call and a price you agree to before we schedule.
Call (669) 359-3289 for a quote.
Below is a look at the plumbing work we handle throughout Campbell and the surrounding Santa Clara County area. Each service is scoped on the phone before anything is scheduled, and you get a price you agree to before we start. Whether the job is straightforward or involves older construction, we walk through what it covers and what it costs on that first call.
| Type of Job | Scope of Work | When to Call | Helpful to Know |
|---|---|---|---|
| Earthquake Gas Shutoff Valves |
| Campbell homeowners who want automatic gas shutoff after seismic activity | Seismic shutoff valves are a practical addition in Santa Clara County given the region's earthquake exposure |
| Faucet & Fixture Installation |
| Dripping faucets, fixture swaps, or new installations at any sink or tub | Most faucet replacements can be scoped and priced accurately on the phone |
| Garbage Disposal Service |
| A disposal that hums but will not spin, leaks, or has stopped working entirely | Replacement units are sized to the sink and the household's use, not just the cabinet opening |
| Leak Detection & Repair |
| Unexplained water bills, wet spots on floors or walls, or pressure drops | Finding the source before opening walls keeps the repair targeted and the scope accurate |
| Tankless Water Heater Installation |
| Homeowners replacing a tank unit or adding on-demand hot water in a space-limited home | Most Campbell homes with natural gas already have the supply line in place, which simplifies the swap |
| Toilet Repair & Installation |
| A toilet that runs, will not flush, leaks at the base, or needs full replacement | A running toilet can waste a significant amount of water before the problem becomes obvious |
| Drain Cleaning & Clog Removal |
| Any drain that is slow, backed up, or repeatedly clogging | Multiple slow drains at once often point to the main line rather than individual fixtures |
| Water Pressure & Shutoff Valve Repair |
| Low pressure at one fixture or throughout the house, or a shutoff that will not close fully | Pressure loss at every fixture usually points to the PRV or the main shutoff, not the fixtures themselves |
| Sewer & Main Line Service |
| Sewage backup, slow drains throughout the house, or a sewer odor that persists | A camera inspection shows root intrusion, grease buildup, or a collapsed section before any digging starts |
| Emergency Plumbing |
| Any situation that is actively getting worse and cannot wait for a scheduled appointment | We are available every day from 8 AM to 11 PM and take short-notice calls for urgent situations |
| Water Heater Repair & ReplacementMost Popular |
| No hot water, a noisy or leaking unit, or a heater that cannot keep up with demand | We scope repair versus replacement on the call so you know the cost difference before committing |
| Pressure-Regulating Valve Installation |
| Homes with high incoming pressure that is stressing fixtures, supply lines, or the water heater | Municipal supply pressure in parts of the Bay Area runs high enough that a PRV is a practical protective measure |
| Slab Leak Detection & Repair |
| Warm floor spots, rising water bills, or pressure drops in homes on slab foundations | Soil movement and aging copper in mid-century Santa Clara County homes make slab leaks a common call here |
| Whole-Home Repiping |
| Homes with recurring pinhole leaks, discolored water, or persistent low pressure across multiple fixtures | Mid-century Campbell homes with original galvanized pipe are a common candidate for a full repipe |
What is the difference between snaking a drain and hydro jetting, and when does one work better than the other?
Snaking breaks up or pulls out a blockage at a specific point in the line. It is effective for most common clogs and is the right first step in most situations. Hydro jetting sends a high-pressure water stream through the pipe and clears grease, mineral buildup, and root debris along the full length of the line rather than just at the blockage point. When a drain backs up repeatedly after snaking, or when a camera shows heavy buildup along the pipe wall, hydro jetting is usually the more thorough answer. We look at what the camera shows before recommending one over the other.
How can I tell whether a clog is at the fixture or further down in the main line?
A single slow drain usually points to a blockage close to that fixture, often in the P-trap or the short section of pipe just behind it. When two or more drains in different parts of the house slow down at the same time, or when flushing a toilet causes a sink to gurgle, that pattern points to a blockage in the main line rather than at any individual fixture. Main line blockages need a different approach than a fixture-level clog, and we ask about that pattern on the call to scope the job accurately before showing up.
How do tree roots get into a sewer line, and what does the repair involve?
Roots follow moisture, and a sewer line that has any small crack or joint gap gives them a path in. Once inside, roots grow and spread, eventually restricting flow or blocking the line entirely. A sewer camera shows how far the intrusion has gone and whether the pipe wall is still intact. If the pipe is structurally sound, hydro jetting can clear the roots and restore flow. If the pipe has cracked or collapsed where the roots entered, that section needs to come out and be replaced. We confirm which situation you are dealing with before recommending a repair path.
Cause Found Before Anything Is Replaced
We diagnose the actual source of the problem before recommending a repair or a replacement. That means pressure testing, camera inspection, or electronic detection where the situation calls for it, so the scope of the job matches what is actually wrong.
What is the difference between a tank water heater and a tankless unit, and which is right for my home?
A tank water heater stores a set volume of hot water and keeps it heated continuously. A tankless unit heats water on demand as it flows through the unit, which means no stored volume and no standby heat loss. Tankless units generally use less energy over time and deliver hot water without a recovery wait, but they require adequate gas supply or electrical capacity and proper venting. The right choice depends on how many fixtures run simultaneously in the home, the existing gas line size, and the available installation space. We walk through those factors on the call so the replacement matches how the household actually uses hot water.
What causes low water pressure throughout the house rather than just at one fixture?
When pressure is low at a single fixture, the cause is usually local: a clogged aerator, a partially closed valve under the sink, or a failing cartridge. When pressure is low throughout the house, the source is further upstream. The most common culprits are a failing pressure-regulating valve, a main shutoff that was not fully reopened after prior work, or a supply line that has narrowed due to mineral buildup or corrosion. We diagnose where the drop is happening before recommending a repair, because the fix at the PRV is different from the fix at a corroded galvanized line.
Do I need to be home while the plumbing work is being done?
For most jobs, yes. Access to the affected fixtures, the main shutoff, and any crawl space or access panel is usually necessary, and someone needs to be available to confirm the scope and sign off on the work when it is complete. For rental properties, a landlord or property manager who can grant access and reach the tenant if needed is typically sufficient. We confirm the access requirements on the call when the job is scoped so there are no delays when we arrive.
Code-Compliant Work on Every Job
Drain and pipe work is carried out to the standards that inspectors in this area enforce. That matters most on sewer line work, repiping, and water heater installations, where the work has to hold up to a future inspection.
When does it make more sense to repipe than to keep repairing the same section of pipe?
A single pinhole leak in an otherwise sound pipe is usually worth a spot repair. When the same section of pipe develops a second or third leak, or when leaks start appearing in different parts of the house at the same time, that pattern tells you the pipe material itself has reached the end of its useful life. In Campbell homes with original galvanized steel supply lines, that deterioration is often widespread by the time the first visible leak appears. A full repipe replaces the aging material throughout the house and restores pressure and flow at every fixture, which is a more durable outcome than repeated spot repairs on pipe that will continue to fail.
How does a hydro jetting service work, and what does it clear that snaking cannot?
Hydro jetting uses a nozzle attached to a high-pressure hose to push water through the pipe at enough force to scour the pipe wall clean. It removes grease that has built up in layers over time, mineral scale, and fine root debris that a snake breaks through but leaves behind. The result is a pipe that flows closer to its original diameter rather than just a path punched through a blockage. We typically run a camera first to confirm the pipe wall can handle the pressure and to see what we are clearing before the jetting starts.
Scope Agreed Before Any Pipe Is Cut
You get the price and the plan on the call, before anyone shows up. If the job changes once it is underway, we explain what we found and confirm the updated scope before the additional work starts.
What should I know about shutoff valves before a plumbing emergency happens?
Knowing where your main water shutoff is and confirming that it closes fully is one of the most practical things a homeowner can do before a problem occurs. In many Campbell homes, the main shutoff is near the street at the meter box or on the exterior wall near the water meter. Valves that have not been turned in years can seize or fail to close all the way, which means when you need to stop the water fast, the valve does not cooperate. We check shutoff valve function as part of any visit where the main supply is involved, and we can replace a valve that no longer closes reliably.
How are estimates and pricing handled before the work starts?
When you call, we scope the job on the phone and give you a price before anything is scheduled. That number covers what we discussed, and you agree to it before we confirm the appointment. If the work uncovers something additional once it is underway, we stop and explain what we found before proceeding. Any change in scope is agreed to before the additional work starts. The price is settled at the start, not after the job is done.
When should I call a plumber rather than attempting a repair myself?
Minor fixture work like replacing a showerhead or a faucet aerator is straightforward for most homeowners. The call to a plumber makes sense when the repair involves supply lines behind a wall, a drain that has not responded to a plunger or a drain cleaner, a water heater of any kind, a toilet that is leaking at the base rather than at the tank, or anything that requires turning off the main water supply. Those situations carry a higher risk of a secondary problem if the repair is not done correctly, and the cost of the call is usually less than the cost of correcting a DIY repair that went further than expected.
Call (669) 359-3289 and we will walk through what the job involves, what it costs, and when we can get to you.
(669) 359-3289